Prijavi se

Zapamti me

KESS V2

Will Kess v2 ot Ktag read and write Abarth 124 Marelli 8GMK?

Purpose: Read a Magneti Marelli 8GMK from an Abarth 124 Optional ECU programming tool: Kess V2 firmware 5.017 and Ktag firmware 7.020 Basic info: 500x with same ecu is supported by Kess 5.017 (protocol 532), but 124 has a new protocol, the 576. Doubt: Is there a possibility to read it with this ksuite updated or users need a new Kess firmware 5.028 with 2.34 (8gmk for 124 wa implemented in 2.32). ...

Pogledaj dalje »

Will MPPS V21 read VAG BOSCH EDC15P+ ECU on bench

Question before entering: I have some trouble with my spare EDC15P+ ECUs.  I have now invested in a MPPS V21 because of its booting capabilities!  But No matter what i do, MPPS keeps saying “Booting of ECU failed” or it freezes during connection establishment. I have tried this om 3 different ECU’s with bad flash and 2 PC’s. The procedure i use: Generic -> Micro Boot -> EDC15P -> Pin 24 t...

Pogledaj dalje »

Free Ksuite 2.23 Winols 2.24 for Reworked Kess and KTag

Free download Kess v2/Ktag software Ksuite 2.23 and Winols 2.24: https://mega.nz/#!PoIm1DJL!G7m_TsNs8dMIiI1EmVc46uqHyFu7yFFcMKen37666qA Here you have full ksuite, with helps and internet protected   What is Ksuite? Ksuite is software to used with Ktag or Kess V2 to read and/or write ECUs. With KESS V2 you programming directly through the OBD port of the vehicle, while with Ktag  you need to t...

Pogledaj dalje »

Volvo V70 EDC15C11 Read and Write by Kess, Ktag, MPPS or FgTech?

Here are optional solutions of Volvo V70 EDC15C11 ECU read and write using different ECU programmers, incl. Kess V2, Ktag, MPPS cable, FgTech Galletto 4 V54. Car: Volvo V70 D5 2004 163hp Ecu: I think the car has either a EDC15C2 or EDC15C11 ecu. (K-suite states EDC15C2) Option 1: You can use Fgtech Galletto V54 Rread/write work only in bootmode at this car. volvo s60 D5 163 hp euro 3 with edc 15c1...

Pogledaj dalje »

How to Convert Ktag Firmware 6.070 to Transdata

Thanks for teamtuner posting for all ecu tuners the real solution for Transdata. It’s a good direction of how to convert your Ktag 6.070 to Transdata. Share it here and hope it helps.   What is Ktag? KTag is perfect for Jtag, BDM and all the Boot application (tricore and ST10). with Ktag you need to take apart the ECU and open it, after you can make the read/write operation. Many ECU has the ...

Pogledaj dalje »

How to Turn Off Mazda RX-8 Speed Limiter by Kess V2

Here’s the turoial to disable the speed limiter on the Japanese ( JPN ) right-hand drive Mazda RX-8 SE 1.3L AT. Disclaimer: The guide was translated from Russian. It is only for education purpose. Credit to  P1on3R91. You are at your risk. In this car, a 180 km / h limiter is installed. It seemed it would be easier to turn it off. But after counting the firmware, I ran into the problem of finding ...

Pogledaj dalje »

China Clone Kess V2 5.017 Red PCB Rework

Bought a Kess V2 5.017 china clone, but no luck. I can try to read but writing is sometimes danger. power supply for akku. When I write flash, the ecu need a lot of power. Searched a lot… thought i should rework the inner board. Then i did something… Transistors: BCR112 MMUN2113 BC817 Murata filters: NFE61PT472C1H9L (connect ground for all of them) Capacitors: 1uF – 35V 220uF – 10V 10uF – 16V tant...

Pogledaj dalje »