Prijavi se

Zapamti me

Fgtech Galletto

Read and Write Bosch ECU MED17.5 with Fgtech Galletto

The ECU is built on the Infineon Tricore TC1766 processor. In the chip of the processor is a flash memory in volume of 1504 bytes and EEPROM in 32 bytes. There are two ways to read-write a block: via the OBD connector and through the BSL bootloader (the so-called boot-mode) Each of the methods has its pros and cons. Read-write via OBD : Pros: -fastly- no breakdown of the ecu is required Cons: -it ...

Pogledaj dalje »

How to Unlock Opel ME7.6.2 ecu

Here are solutions to unlock this ECU: Astra H 2.0 Bosch Me7.6.2. Q: Hello can tell me any good tool for reading opel ecu for chip tuning. Bosch ME.7.6.2 – Z16LET – Z14XEP Astra H and Corsa. Option 1: SMOK opel all from smok !!!! can help with this ecu Supported ECU CAN and available functions: Bosch ME762 Read EE, Read PIN, Read/Write KM, Change VIN, Reset ECU Supported ECU Kline and available fu...

Pogledaj dalje »

How to Unlock VAG PCR 2.1 ECU with Fgtech Galletto on Bench

How to unlock SIMOS PCR 2.1 ECU from 2011 1.6 TDI VAG to remap on the bench using FG TECH galletto. How FGTech Galletto 4 V54 remap Simos PCR 2.1 ECU? Step1. Open Simos PCR 2.1 ECU, connect resistor and make jumper. Step2. Unlock Simos PCR 2.1 ECU on bench then close it. Step3. Put ECU inside car, read it again via OBD and then modify that file. Step4. Now you can use FGTech Galletto 4 V54 to read...

Pogledaj dalje »

Guide: How to install Fgtech Galletto V54 on Windows 7

Fgtech Galletto 4 V54 Windows 7 has been tested to work perfect. But for some users, there are some troubles after Galletto v54 installation, e.g. Galletto 4 v54 won’t start/run after install. Here is the how-to’s and FAQs of Fgtech V54 Windows 7 installation. THE MOST IMPORTANT: You have to REMOVE ALL OLD FGtech FILES from the system before installing Galletto V54. Guides: How to install Fgtecg G...

Pogledaj dalje »

Fgtech Galletto 4 V54 China clone vs. EU Clone

This is FGtech Galletto 4 v54 PCB design and component position from EU to China. Galletto V54 EU clone: Eu pcb its Gold immersion and not hot air surface level like China. You can change a lot of parts but will not be the same FGtech Galletto 4 V54 china clone: Galletto V54 china version 1: Galletto V54 china version 2: Galletto china version 1 and version 2 cannot work at all, so totally crap. U...

Pogledaj dalje »

Fgtech, Ktag, Kess V2 unlock & flash PCR 2.1

This is a thread- “100% tested /worked bench unlock and flashing (read and write ) on pcr2.1”, posted in digital-kaos.co.uk. Good information, so i share this thread again. No one but yourself should take responsibility of what you will try. Big thanks to gzk in France did the following write-up of reviews of pcr2.1 bench unlock and flashing. Here you go. (src: http://www.digital-kaos.co.uk/…...

Pogledaj dalje »

Fgtech Galletto V54 clone write safety PCR 2.1

Here is the instruction on writing stately PCR 2.1 with Fgtech Galletto 4 V54 master clone for those who do not have original tools.  All you need it's UPA USB and Galletto V54 China clone! Credits to Mr. mercas who made this tutorial. On forum exist a lot of threads with bricked ecu's because Galletto,Kess or other tool don't unlock ok every time this ecu on bootmode, or ecu was already unlocked ...

Pogledaj dalje »