Prijavi se

Zapamti me

Kess V2

Ktag Kess V2 Full Set 22 BDM Probe Adapters List

The full set BDM probe adapters for KTAG, KESS V2, KTM100 Dimsport, Trasdata chip tuning tools is available in obdii365.com.   Function: To use with ECU programmers to read  Denso, Marelli, Bosch, Siemens ECUs. Features: Adapter width: ~60mm width for original BDM Probe, not for low quality plastic with 40mm width. Adapter thickness: 2mm Adapter colour: Green A full set comes with 22 BDM adap...

Pogledaj dalje »

How to use Kess V2 Ktag to Unlock CRP3 LPC2478 via J-link

As you know, for crp3 we can do the trick for unlock crp3 heating on Ktag or Kess V2 programmer or buy a new NXP and write it (only one time) Here are some questions & answers on Google form, questions about “how will you use J-ink if its crp3 ?”… Q: Can I update NXP directly if at this moment I have Ktag 6.070? Or I will need to replace it with new one and then to update to 7.030 ? A: if your...

Pogledaj dalje »

Kess V2 V5.017 Red Clone New PCB and Old PCB Comparison

There are differences between the Kess V2 5.017 red pcb boards. Both work good? Let’s see the two boards here and read reviews to find out the truth. Kess V2 5.017 Version 1: Most of the boards look like this   Kess V2 v5.017 Version 2: board with different reworked parts: 1.the left upper corner and the lower right corner notch size is not the same 2.More than buzzer 3.WFs = Infineon, BCR112 NPN ...

Pogledaj dalje »

Kess V2 V5.017 Original and Clone Difference

What’s the exact difference between kess v2 slave or master? It’s better to buy original or clone are good? It all depends. Kess v2 good clone used be ok for older ecus only, but now also work great with newer ones. and with a slave you will have to rely on the master for your maps whaere as if you have a master you can write your own or choose where you get them from. Kess v2 master: If you have ...

Pogledaj dalje »

How to Write Subaru ECU with Kess V2 by OBD

Read many posts to have the pin diagrams for the Kess v2 ecu tuning master Subaru cable. And luckily, i found this: The man has a genuine kess subaru cable., and measured the cable for someone in need.   But it seems there is something wrong. He has the red obd connector the wrong way round A mate in the forum also says ”what you have as pin 1 is actually pin 9 and what you have as pin 15 or ...

Pogledaj dalje »

How to use Ktag 7.020 to read Toyota diesel engine ecu

Question before entering: I have a Toyota with d4d engine 2.2d 177hp Which tool can read and write   Solution: kess v2 5.017 write it on CAN Line But you have to do an original because you can't read it New Ktag clone should do it on bench in Jtag. X17 official web and write it without problem by OBD or by pinout. But only in CAN LINE and some think in Kline but you have to buy or build an ad...

Pogledaj dalje »

OBD read EDC17C46 ECU with Kess V2 or MPPS V18

What’s the difference of EDC17C46 OBD reading by MPPS V18 & Kess V2 master? Look here:   With Kess v2: You can write boot readout or frf->bin file with kess obd, but you need to choose correct protocol. Kess will automatically do tprot patch in this procedure. But you need to know what you are doing. Checksum correction from alientech is sometimes a little bit poor if you change someth...

Pogledaj dalje »