Prijavi se

Zapamti me

AT-200

CGDI FC200 and CG AT-200 Comparison

CG FC200 ECU Programmer & ISN OBD Reader, the full version of CG AT200, comes with all Authorization from CG AT200 without paying extra money. FC200 ECU programmer can perform ECU/ EGS clones, can process data, can read and write ISN, can perform disassembly matching, VIN modification and DTC shielding, etc. CG FC200 ECU clone supported models: 4200 Kinds of ECU, 3 Types of operation modes, co...

Pogledaj dalje »

How to Read BMW F22 ECU Mevd17.2 with AT-200?

CG AT-200 is able to read BMW ECU Mevd17.2 on Bench in 3 minutes. Please read this article for the procedure.   F22 with N20 engine, took 2 minutes to remove from the car.     Connect to one CG AT-200.       Look at the wire connected with CG AT-200 and N20 engine box.       Connect to one adjustable power supply which can ensure stable voltage.   ...

Pogledaj dalje »

How to use AT-200 to Clone BMW MSV80?

I’d like to share my experience with the AT-200 ECU Programmer and MSV80 unlock upgrade.  I had three codes on a customers’ vehicle that came in 2011 BMW 328Cic: 2E7C BSD (Bit-Serial Data Interface) data bus communications fault 2F71 Digital Motor Electronics (DME): electronics box fan, activation 2B3D Diagnostic Module Tank Leakage (DMTL), system fault   While it’s possible all these present...

Pogledaj dalje »

AT-200 Read and Write BMW B48 EEPROM Flash

CG AT-200 ecu programmer newly updated BMW F and G series B48 B58 ISN reading, EEPROM & FLASH data reading and writing on bench mode. Example: AT-200 read B48 G series ISN on bench Read ISN Select Brand BMW-> BMW-MG1CS002/MG1CS003_B48/B58_G in AT200 software Check wiring diagram to at200 Connect B48 DME ecu with AT-200 via tester cable     Identify DME information (click to enlarg...

Pogledaj dalje »

What Device to Read and Write Mercedes SIM271 ECU?

Question: Need to swap a Mercedes SIM271 ECU. Any idea which tool can do it? Option 1:  BitBox Mercedes SIM271 Module BitBox is the module for reading and writing on the bench by CAN-bus for petrol Mercedes-Benz W204/W212 vehicles with Siemens/Continental SIM271 ECUs. The J2534 Tactrix Openport 2.0 interface, BitSoftware Senselock USB dongle and Universal Bench Cable are required to work with BitB...

Pogledaj dalje »

AT-200 Read BMW MSD85 MSD87 MSV90 ISN code

AT200 programmer is confirmed to work good with BMW MSD85 MSD87 MSV90 – able to read isn without any issue! Purpose: To check if the AT200 programmer is working or not source: http://www.obdii365.com/wholesale/bmw-at200-ecu-programmer.html Function for the test: Read ISN BMW DMEs for the test: MSD85 MSD87 MSV90 Steps: Step 1: install and run AT-200 programming software Step 2: connect the AT-200 w...

Pogledaj dalje »

CGDI AT-200 review on BMW DME MSV90 Reading

AT-200 ecu programmer is a new solution to read/write/clone BMW ECU and read ISN code. Support almost all the BMW ECU model for reading and writing: MSV90 MSD85 MSD87 N2055 B38 B48.  Its best solution for changing used computer after broken (Only car computer repair essential. ) BMW AT-200 is able to read BMW ISN Code from DME when do all key lost for BMW 3 Series 5 Series 7 Series X5 X6 GT535 Six...

Pogledaj dalje »