Prijavi se

Zapamti me

kess v2 5.017

Kess V2 Flashes Chevrolet Cruze ECU Simtec 76.1

Today I was flashing the engine control unit on the Chevrolet Cruze A J300 2012Y 1.8L AT. The car arrived with errors after the service, where they changed the rear lambda, put a trick, checked the wiring, cut the cat, etc: The owner of the car is already tired of all this, so it was decided to flash the calibration under E2. What I actually did)) Siemens Simtec 76.1 control unit : For the firmwar...

Pogledaj dalje »

Where to Download Ksuite 2.47 for Kess V2 Clone?

Ksuite 2.47 software for Kess V2 firmware 5.017 clone free download resource is provided below: No need HWID and KG. Unpack DLL from archive in folder Ksuite/DLL.   Ksuite_2.47 for Kess v2 5.017 clone https://mega.nz/#!Sx8i3JQK!XC2WUVHJCSf3bKg4niJhyaL3444uz8GcSvCXmZi4jeI DLL https://mega.nz/#!C4kHVTzb!UOwqWrLM8-jr86MJLCLhZw-srYuAklVUOv0V6PPSSDA (Big thanks to svvag2000. You are at your risk) ...

Pogledaj dalje »

Will Kess v2 ot Ktag read and write Abarth 124 Marelli 8GMK?

Purpose: Read a Magneti Marelli 8GMK from an Abarth 124 Optional ECU programming tool: Kess V2 firmware 5.017 and Ktag firmware 7.020 Basic info: 500x with same ecu is supported by Kess 5.017 (protocol 532), but 124 has a new protocol, the 576. Doubt: Is there a possibility to read it with this ksuite updated or users need a new Kess firmware 5.028 with 2.34 (8gmk for 124 wa implemented in 2.32). ...

Pogledaj dalje »

Free Ksuite 2.23 Winols 2.24 for Reworked Kess and KTag

Free download Kess v2/Ktag software Ksuite 2.23 and Winols 2.24: https://mega.nz/#!PoIm1DJL!G7m_TsNs8dMIiI1EmVc46uqHyFu7yFFcMKen37666qA Here you have full ksuite, with helps and internet protected   What is Ksuite? Ksuite is software to used with Ktag or Kess V2 to read and/or write ECUs. With KESS V2 you programming directly through the OBD port of the vehicle, while with Ktag  you need to t...

Pogledaj dalje »

How to Turn Off Mazda RX-8 Speed Limiter by Kess V2

Here’s the turoial to disable the speed limiter on the Japanese ( JPN ) right-hand drive Mazda RX-8 SE 1.3L AT. Disclaimer: The guide was translated from Russian. It is only for education purpose. Credit to  P1on3R91. You are at your risk. In this car, a 180 km / h limiter is installed. It seemed it would be easier to turn it off. But after counting the firmware, I ran into the problem of finding ...

Pogledaj dalje »

Kess V2 5.028 vs Kess V2 5.017

KESS V2 5.017 updated version – KESS V2 5.028 is gonna happen. So, what’s the difference between Kess V2 firmware 5.028 and Kess V2 firmware 5.017?   Here you go.   1- New firmware: 2018 Kess V2: firmware 5.028 2017 Kess V2: firmware 5.017   About components improvement: Kess V2 5.028: unknown components improvement Kess V2 5.017: components improvement released notes – 1.. the left...

Pogledaj dalje »

Kess V2 V5.017 Red Clone New PCB and Old PCB Comparison

There are differences between the Kess V2 5.017 red pcb boards. Both work good? Let’s see the two boards here and read reviews to find out the truth. Kess V2 5.017 Version 1: Most of the boards look like this   Kess V2 v5.017 Version 2: board with different reworked parts: 1.the left upper corner and the lower right corner notch size is not the same 2.More than buzzer 3.WFs = Infineon, BCR112 NPN ...

Pogledaj dalje »