Prijavi se

Zapamti me

kess v2 v5.017

How to Install Kess V2 V2.80 for Firmware 5.017?

Kess V2 Ksuite 2.80 software can be installed on win7, win8 and win10, and it is multilingual. This article is on how to install Ksuite 2.80 on win10 64bit and then read ECU Volkswagen Passat CC Bosch MED17.5 OBDII.   Ksuite V2.80 free download: Source 1. https://mega.nz/file/tk1QEKIS#T66cPJFkcciNfPXTfVj5CVJSZy8M6DcKpMgKBbQ03rM Size: 1.7GB Password: No need   Source 2. https://share.weiyun.co...

Pogledaj dalje »

Free Ksuite 2.23 Winols 2.24 for Reworked Kess and KTag

Free download Kess v2/Ktag software Ksuite 2.23 and Winols 2.24: https://mega.nz/#!PoIm1DJL!G7m_TsNs8dMIiI1EmVc46uqHyFu7yFFcMKen37666qA Here you have full ksuite, with helps and internet protected   What is Ksuite? Ksuite is software to used with Ktag or Kess V2 to read and/or write ECUs. With KESS V2 you programming directly through the OBD port of the vehicle, while with Ktag  you need to t...

Pogledaj dalje »

How to Turn Off Mazda RX-8 Speed Limiter by Kess V2

Here’s the turoial to disable the speed limiter on the Japanese ( JPN ) right-hand drive Mazda RX-8 SE 1.3L AT. Disclaimer: The guide was translated from Russian. It is only for education purpose. Credit to  P1on3R91. You are at your risk. In this car, a 180 km / h limiter is installed. It seemed it would be easier to turn it off. But after counting the firmware, I ran into the problem of finding ...

Pogledaj dalje »

Kess V2 read and write Renault Lagoon 3 EDC17CP58

Kess V2 manual: How to read/write Renault edc17cp58 ECU through BOOT: Note: When writing the modified file, the checksum of the data may last several minutes, depending on the performances of your computer. Preparation before Renault ECU read/write Remove the ECU from the vehicle; Open the ECU, taking care in not damaging the parts inside; Reconnect the ECU to the vehicle and start the engine, in ...

Pogledaj dalje »

Kess V2 V5.017 Red Clone New PCB and Old PCB Comparison

There are differences between the Kess V2 5.017 red pcb boards. Both work good? Let’s see the two boards here and read reviews to find out the truth. Kess V2 5.017 Version 1: Most of the boards look like this   Kess V2 v5.017 Version 2: board with different reworked parts: 1.the left upper corner and the lower right corner notch size is not the same 2.More than buzzer 3.WFs = Infineon, BCR112 NPN ...

Pogledaj dalje »

Kess V2 V5.017 Original and Clone Difference

What’s the exact difference between kess v2 slave or master? It’s better to buy original or clone are good? It all depends. Kess v2 good clone used be ok for older ecus only, but now also work great with newer ones. and with a slave you will have to rely on the master for your maps whaere as if you have a master you can write your own or choose where you get them from. Kess v2 master: If you have ...

Pogledaj dalje »

OBD read EDC17C46 ECU with Kess V2 or MPPS V18

What’s the difference of EDC17C46 OBD reading by MPPS V18 & Kess V2 master? Look here:   With Kess v2: You can write boot readout or frf->bin file with kess obd, but you need to choose correct protocol. Kess will automatically do tprot patch in this procedure. But you need to know what you are doing. Checksum correction from alientech is sometimes a little bit poor if you change someth...

Pogledaj dalje »