Prijavi se

Zapamti me

KESS V2

How to Convert Ktag Firmware 6.070 to Transdata

Thanks for teamtuner posting for all ecu tuners the real solution for Transdata. It’s a good direction of how to convert your Ktag 6.070 to Transdata. Share it here and hope it helps.   What is Ktag? KTag is perfect for Jtag, BDM and all the Boot application (tricore and ST10). with Ktag you need to take apart the ECU and open it, after you can make the read/write operation. Many ECU has the ...

Pogledaj dalje »

How to Turn Off Mazda RX-8 Speed Limiter by Kess V2

Here’s the turoial to disable the speed limiter on the Japanese ( JPN ) right-hand drive Mazda RX-8 SE 1.3L AT. Disclaimer: The guide was translated from Russian. It is only for education purpose. Credit to  P1on3R91. You are at your risk. In this car, a 180 km / h limiter is installed. It seemed it would be easier to turn it off. But after counting the firmware, I ran into the problem of finding ...

Pogledaj dalje »

How to Unlock Opel ME7.6.2 ecu

Here are solutions to unlock this ECU: Astra H 2.0 Bosch Me7.6.2. Q: Hello can tell me any good tool for reading opel ecu for chip tuning. Bosch ME.7.6.2 – Z16LET – Z14XEP Astra H and Corsa. Option 1: SMOK opel all from smok !!!! can help with this ecu Supported ECU CAN and available functions: Bosch ME762 Read EE, Read PIN, Read/Write KM, Change VIN, Reset ECU Supported ECU Kline and available fu...

Pogledaj dalje »

Kess V2 5.028 vs Kess V2 5.017

KESS V2 5.017 updated version – KESS V2 5.028 is gonna happen. So, what’s the difference between Kess V2 firmware 5.028 and Kess V2 firmware 5.017?   Here you go.   1- New firmware: 2018 Kess V2: firmware 5.028 2017 Kess V2: firmware 5.017   About components improvement: Kess V2 5.028: unknown components improvement Kess V2 5.017: components improvement released notes – 1.. the left...

Pogledaj dalje »

Kess V2 read and write Renault Lagoon 3 EDC17CP58

Kess V2 manual: How to read/write Renault edc17cp58 ECU through BOOT: Note: When writing the modified file, the checksum of the data may last several minutes, depending on the performances of your computer. Preparation before Renault ECU read/write Remove the ECU from the vehicle; Open the ECU, taking care in not damaging the parts inside; Reconnect the ECU to the vehicle and start the engine, in ...

Pogledaj dalje »

Ktag Kess V2 Full Set 22 BDM Probe Adapters List

The full set BDM probe adapters for KTAG, KESS V2, KTM100 Dimsport, Trasdata chip tuning tools is available in obdii365.com.   Function: To use with ECU programmers to read  Denso, Marelli, Bosch, Siemens ECUs. Features: Adapter width: ~60mm width for original BDM Probe, not for low quality plastic with 40mm width. Adapter thickness: 2mm Adapter colour: Green A full set comes with 22 BDM adap...

Pogledaj dalje »

How to use Kess V2 Ktag to Unlock CRP3 LPC2478 via J-link

As you know, for crp3 we can do the trick for unlock crp3 heating on Ktag or Kess V2 programmer or buy a new NXP and write it (only one time) Here are some questions & answers on Google form, questions about “how will you use J-ink if its crp3 ?”… Q: Can I update NXP directly if at this moment I have Ktag 6.070? Or I will need to replace it with new one and then to update to 7.030 ? A: if your...

Pogledaj dalje »