Prijavi se

Zapamti me

ktag

Possible to do immo off by kess v2?

Here are handy tips and guides for you guys who are trying to do immo off by kess v2 ecu master. What is immo off? And what is partial immo off? IMMO off is simply a modded dump of the ecu flash or eeprom or separate immo box to tell the car no immobilisers function In some immo files you see the letters T or P . T means total, so immo off/disabled. P stands for Partial that one is used to make th...

Pogledaj dalje »

How to Clone BMW MSD80 MSD85 MSD81 MSD87 ECUs with Ktag

How to: clone Siemens MSDxx (MSD80, MSD81, MSD85, MSD87, MSD85.4) ECUs for BMW SSM vehicles using original Ktag K-suite ecu programmer. To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair. After opening the ECU and before proceeding with reading and/or programming, you are...

Pogledaj dalje »

Read VAG EDC17CP44 with Kess v2, Ktag, or Fgtech ?

Possible to read/write VAG ECU EDC17CP44 via OBD? And which tool can do it? Here you go.   EDC17CP44 details: Information: BSL130 no BSL131 yes BSL132 yes BSL-ADP required   ECU pins: Use Plug – Pin 12V T91 – Pin 5 Ign T91 – Pin 50 Gnd T91 – Pin 1 Can+ T91 – Pin 79 Can- T91 – Pin 80 S1 T105 – Pin 18 S2 T105 – Pin 21   Pictures: Vehicles with ECU EDC17CP44: VEHICLES / INFO ECU TYPE P...

Pogledaj dalje »

Nissan 350Z ECU Remapping using Ktag on Bench

Today we have been tuning Nissan 350Z’s for increased power. Although they power gain is only around 10-15BHP and 20Nm of torque they drive so much smoother. From the initial test drive on the road the mid range punch becomes noticeable pulling stronger to the rev limiter in every gear. We would say this feels more like 20+bhp increase on the road.   The earlier 350Z uses a Hitachi ECU that c...

Pogledaj dalje »

How to use KTMFlash ECU Programmer Switch board with Ktag/Openport?

What’s KTMFlash? The KTMFlash is a ECU Programmer & transmission power upgrade tool which can read the chip data, change the engine computer, read transmission data etc at a high speed. KTMflash Functions: 1.Read the car ecu via OBD. 3.Read the BOOT mode according to the chip model 4.Read the encrypted ECU password (Read the password of encrypted ECU first, then read data) 5. Support cars made...

Pogledaj dalje »

Will Kess v2 ot Ktag read and write Abarth 124 Marelli 8GMK?

Purpose: Read a Magneti Marelli 8GMK from an Abarth 124 Optional ECU programming tool: Kess V2 firmware 5.017 and Ktag firmware 7.020 Basic info: 500x with same ecu is supported by Kess 5.017 (protocol 532), but 124 has a new protocol, the 576. Doubt: Is there a possibility to read it with this ksuite updated or users need a new Kess firmware 5.028 with 2.34 (8gmk for 124 wa implemented in 2.32). ...

Pogledaj dalje »

Bosch MEV17.4.2 Reading with Ktag 7.020 on Bench

How to: read a Citroen C4 1.6 gasoline engine Bosch MEV17.4.2 from PSA group. And was read in boot mode using KTag 7.020.   Bosch MEV17.4.2 == MEV174 reading with Ktag Open ECU Follow wiring diagram to connect ECU with K-tag Open Ksuite software Select Bosch MED 17.4.2 Tricore    Select Plug 305 Bosch MED174/MEV174 IROM TC1767 PSA (P305) Read ECU data Ktag 7.020 read MEV17.4.2 data success. S...

Pogledaj dalje »