Prijavi se

Zapamti me

Xhorse VVDI2

How to Repair Xhorse VVDI2 if not connected with OBD2?

Here’s the customer solution to Xhorse VVDI2  not connected by OBD2 problem. Disclaimer: You are at your risk. Problem: Today my VVDI2 is no longer connected by OBD2, it has been short to negative. This component was burned (make smoke), I took it and at least UDS protocol is working, I did not test in Kline. Can you tell me which component to send and replace on the board?     DIY Solut...

Pogledaj dalje »

VVDI2 possible to change Audi A3 8P 2005 BKC cluster?

Audi A3 8P 2005 BKC change cluster with VVDI2 OK? If not, how to do? Question: Audi A3 8P 2005 BKC, i want to change the cluster, but vvdi2 wouldn’t read the old IC. Answer: It’s 8P VDO dash with Fujitsu. VVDI does not support them. Read Immodata from ECU (CS, Login, MAC and immo id) get 7th byte from key and transfer to new dash. Question: Thanks your reply. I got all data what i need. From ECU: ...

Pogledaj dalje »

FAQ Xhorse VVDI2 Audi A3 All Keys Lost

Question 1: can you advice why this xhorse vvdi2 tool is not reading Audi A3 cluster Micronas cdc3217g? I know AVDI can read in 2min. Never the less is it possible to get 7 byte CS from ECU to make dealer key? Answer: You can get only 6 bytes from ECU. Reading Micronas in-circuit is also possible with a good programmer to get 7 bytes. Question 2:Thanks mate I know but I do not want to go stripping...

Pogledaj dalje »

How to Learn Audi A6 Q7 Allroad Key with VVDI2

Here’s the solution for Xhorse VVDI2 prepares Audi A6/Q7/Allroad 4th immobilizer dealer key successfully but fail to star car. Reason: The step for key learning is skipped/wrong. Solution: please check guides below to to learn the key correctly. Audi 4th Immobilizer system- Audi A6/Q7/Allroad This type use MEGAMOS 8E transponder If you want prepare a new dealer key, you must know the total 12 byte...

Pogledaj dalje »

Program Land Cruiser 2013 Smart Key with VVDI2 and VVDI Prog

Our customer has successfully programmed a smart key to a Toyota Land Cruiser GXR 2013 Middle East model using VVDI2 and VVDI Prog programmer when all keys have lost. Step 1: Read EEPROM data Remove IMMO box under dashboard Desolder IC 93C86 EEPROM chip with a hot gun Solder the EEPROM chip to adapter and connect vvdi prog with laptop Open vvdi-prog software Select EEPROM/FLASH->ST->M93C86 R...

Pogledaj dalje »

How to Make VAG 4th IMMO key with VAG OBD cable and VVDI2

When we cannot read immo data from OBD using OBD device, we cannot continue making new keys. With VAG OBD Helper cable, you can obtain immo data easily via OBD, especially VAG 4th immobilizer system (NEC24C32 NEC24C64, NEC35XX, Johnson MQB A4, A5 etc BCM), both add key and all keys lost. Here’s the guide to program new dealer key using VAG OBD cable and Xhorse VVDI2. (The cable can be used with ot...

Pogledaj dalje »

How to Enable Free MQB Activation for Xhorse VVDI2

Good News!!!  Great gift from Xhorse. Since today vvdishop.com is able to enable for free MQB activation (VV-05) for all user who have VVDI2 Full.  You can buy ID48 96bit cloning and get free MQB, but if you no need copy 48, you can request free MQB. 1.Just for oversea VVDI2 users. 2. Make sure your VVDI2 is full version (VV-01)VAG 4th immobilizer YES (VV-02)VAG 5th immobilizer YES (VB-01)BMW OBD ...

Pogledaj dalje »