Prijavi se

Zapamti me

Arhive

Xhorse VVDI Prog Failed to Read 3K85K MCU Solution

Problem: I can’t read the chip  MC68HC9 Mask 3k85k with the Xhorse VVDI Prog programmer. It says “Try frequency failed chip unconnected” (00).         Solution: I figured it out. I set the voltage VCC to 4.5 instead of 5 and everything worked out. www.vvdishop.com

Pogledaj dalje »

Quick Guide to Tell if PSA MD1CS003 ECU is Locked or Not

Entry question: Will Alientech kess3 read and write 2021 Citroen Berlingo Bosch MD1S003 ECU?     Yes, You can read with confidence. Bench mode. This ECU is not locked. How to Tell if PSA MD1CS003 ECU is Locked or Not?   Most MD1 ECUs after mid-2020 or later are locked. Have tried a few 2021 PSA and were locked. For PSA MD1CS003 ECU, check part number. Here is a tip to identify if th...

Pogledaj dalje »

“Pogresna intuicija, ma nije ovo licitacija, nema te nema sto godina, ne secam ti se ni imena…”

My dear friends, Welcome to my Blog! I would like to use it for only one purpose and that is sharing my life story. My father was a shadow. My father was actually an as**ole who ran away after one crazy night spent with my mom. Actually, my mom gave me up for adoption after I had been born. I grew up in this little village I should not say its name. There were plenty of kids. There was 10 of us &#...

Pogledaj dalje »

How to Add Skoda Octavia 2016 MQB Key with VVDI Key Tool Plus via OBD

Successfully added a spare key to Skoda Octavia III 2016 VRs MQB using Xhorse VVDI Key Tool Plus. – Start to finish ~8min. – KD ZB remote. – All step obd. – Remote sync needed after programming (driver door manual procedure). VDO MQB35xx 2014-UDS Chip type: D70F3537     Select Key Adding automatic wizard menu. Step 1: Read and save eeprom Step 2: Read and save immo data. Step 3: Reset in...

Pogledaj dalje »

How to Use Autel IM508 with Godiag GT107 to Clone Benz 7G Gearbox

Tutorial: How to renew and clone Mercedes Benz 7G Tronic transmission gearbox TCU with Autel step-by-step.   It is a 2010 Mercedes GLK350, the shop just replaced the 7-speed automatic transmission with the used one. What we are going to be doing is cloning the TCU now over here on the ground. Got Autel IM508 or IM608 connected with the XP400 then over the OBD plug.   This is the Godiag G...

Pogledaj dalje »

VVDI Key Tool Max Pro Device Self Test Procedure

If your Xhorse VVDI Key Tool Max pro fails to start communication with vehicle and asks to check if the OBD wiring is normal, follow guide below to do a device self test.     VVDI Key Tool Max Pro Self Test In main menu select IMMO Programming Select More Functions Press Device Test Select K-line Test Short Connect PIN7 and PIN15 with the OBD connector. If Key Tool Max Pro says the test ...

Pogledaj dalje »

How to CLone and Adapt Audi BCM2 Module?

Question 1: Is it possible to clone bcm2 with Xhorse vvdi key tools plus or vvdi2? Need to clone BCM 2 Part number is 4H0907064FT 0560 So i got used BCM2 which is the exact same part number. Original BCM2 is locked, so i read DATA1 and DATA2 and make service data with VVDI2. Then i tried to clone on Used BCM2, but BCM is not locked, so i could read Dflash, and Pflash, in this case, how can i clone...

Pogledaj dalje »